Sunrise Roof Pros provides professional metal roofing in Sunrise, FL for residential and commercial properties across west Broward County. Metal earns its place on a Broward house for one reason: it takes the covering off the list of things that can slide, crack or fail at a mortar bed. What it does not do is remove the underlayment from the equation, and people buy metal believing it does.
Under a standing seam panel the membrane is still the water plane at every penetration, every valley and every panel end lap. The difference is temperature. Panels run hot enough that ordinary self-adhered underlayment can soften and lose its bond, so we specify a high-temperature self-adhered membrane rated for it and let nobody value-engineer that line out. Panel end laps and eave closures get the same membrane treatment, because that is where driven rain gets in.
Panel choice follows exposure. A 26-gauge Galvalume or aluminum standing seam with concealed clips lets the panel move with the day's heat and keeps fasteners out of the water plane, which is what you want on a house. Exposed-fastener panels are cheaper and fine on a detached shop or a barn, where several hundred neoprene washers ageing in the sun is a maintenance item rather than a ceiling.
Metal compatibility is where cheap metal roofs go wrong. Mixing an aluminum panel with a steel clip, or a zinc-coated screw with a copper flashing, sets up galvanic corrosion at the joint, and it shows as a rust weep down a good panel years before the panel itself is worn. We keep the panel, the clip, the fastener and the trim in one compatible family and name each of them on the proposal.
Converting a tile roof to metal is lighter, not automatically simpler. The deck was fastened for a heavy covering, the fascia and rake detailing were built for tile thickness, and a metal field over that geometry needs new trim rather than adapted trim. It is a good move on a low-pitch roof with long clean runs and a poor one on a complicated hip roof with a dozen valleys.
We will talk you out of metal on two roofs. One is a heavily cut-up roof where the price is driven by flashing labor and the result is a hundred joints instead of a hundred tiles. The other is a house with an association tile requirement, where the panel is the wrong argument to be having with your board.
Our licensed and insured team brings the right materials and equipment to every job — two-ply tile underlayment with a mineral-surfaced cap sheet, RAS 118 mortar-set hip and ridge, RAS 120 mechanically fastened tile, tin-capped base sheet fastening on a 12-inch grid, eave riser and anti-ponding strip, two-component polyurethane tile adhesive — and backs the work with a written workmanship warranty. We serve Sunrise and nearby communities including Plantation, Davie, Weston, Tamarac.
What We Handle
Everything our metal roofing in Sunrise covers
One crew, one point of contact, and the full range of metal roofing work in Sunrise, FL. If it is on this list we do it in house rather than handing it to a subcontractor:
- metal roofing
- standing seam metal roof
- 26-gauge Galvalume panels
- concealed clip metal roof
- exposed fastener panel roof
- metal roof over tile deck
- high-temperature underlayment
- metal roof installation
- metal roof repair
- aluminum roof panels Florida
- metal roofing near me
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Sunrise services.
Materials, equipment and how we do metal roofing
The difference between metal roofing that lasts and metal roofing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with two-ply tile underlayment with a mineral-surfaced cap sheet, RAS 118 mortar-set hip and ridge, RAS 120 mechanically fastened tile, tin-capped base sheet fastening on a 12-inch grid, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Sunrise job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in west Broward County means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do metal roofing outside Sunrise
Sunrise Roof Pros covers Sunrise and the surrounding communities of west Broward County. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Metal Roofing in Plantation, FL — Broward County, population 91,750
- Metal Roofing in Davie, FL — Broward County, population 105,691
- Metal Roofing in Weston, FL — Broward County, population 68,107
- Metal Roofing in Tamarac, FL — Broward County, population 71,897
- Metal Roofing in Lauderhill, FL — Broward County, population 74,482
- Metal Roofing in North Lauderdale, FL — Broward County, population 44,794
Start on the Sunrise Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Sunrise Chooses Sunrise Roof Pros
- ✓We quote from an opened assembly, lifting tile at valleys, penetrations and field corners rather than pricing from a drone photograph.
- ✓Every proposal names the underlayment system, the tile attachment standard and the Miami-Dade Notice of Acceptance numbers we are working to.
- ✓Deck repair is a written unit rate with an allowance, so soft plywood found after tear-off is not a surprise change order.
- ✓We will tell you when a repair beats a replacement, and we will decline tile sealing packages and coatings sold as underlayment substitutes.
The standards behind metal roofing
Quality here is not a matter of opinion — it is written down. The metal roofing work we do in Sunrise follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every metal roofing project in Sunrise gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free metal roofing free estimate in Sunrise, or request a quote and we'll get right back to you.